- 您现在的位置：买卖IC网 > Sheet目录321 > DM163030 (Microchip Technology)KIT DEV PICDEM LCD2
PICDEM? LCD 2 DEMONSTRATION
KIT USER ’S GUIDE
Chapter 2. Getting Started
The PICDEM LCD 2 may be used as a stand-alone board with a preprogrammed
device, with an In-Circuit Emulator (ICE) or with an In-Circuit Debugger (ICD). For a list
of PIC ? microcontroller compatible ICEs or ICDs, please refer to the “Microchip
Development Systems Ordering Guide” (DS30177) .
2.1
PICDEM LCD 2 AS A STAND-ALONE BOARD – PREPROGRAMMED DEVICE
The PICDEM LCD 2 may be demonstrated immediately by following the steps listed
below:
? Apply power to the PICDEM LCD 2. For information on acceptable power
Note:
In the event that the preprogrammed PICDEM LCD 2 Demonstration Board
with the PIC18F85J90 PIM does not operate, check the following
conditions:
- The jumper, J15, is configured as per the power supply used. The slide
switch, S6, is switched to C.
- JP1, JP2, JP6, JP18 and JP19 are connected.
- The middle two jumpers of J14 are connected.
- JP9 and JP10 are connected.
- J11 connecting POT to AN0 and JP17 connecting V CC to I/O.
The status of all other jumpers will not affect the preprogrammed
demonstration.
To reprogram the sample device, the following will be necessary:
1. User source code may be programmed to the device or the sample program may
be restored from the file on the included CD-ROM.
2. An assembler, such as the MPASM? Assembler (available with MPLAB IDE), or
a compiler, such as MPLAB C18 C Compiler (PIC18XXXX/18XXJXX devices
only) must be used.
Source code must be assembled or compiled into a HEX file before it can be
programmed into the device. Microchip Technology’s MPASM Assembler or
MPLAB C18 C Compiler may be used. Both are compatible with MPLAB IDE;
however, other assemblers/compilers may be used.
3. Once the sample program is in the HEX file format, it can be programmed to a
Flash device using an MPLAB ICD 2 or PM3 with an ICSP? module. Microchip
Technology’s MPLAB ICD 2 is compatible with MPLAB IDE.
If the code protection bit(s) have not been programmed, the on-chip program
memory can be read out for verification purposes.
? 2010 Microchip Technology Inc.
DS51662C-page 15
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
DM163035
KIT DEVELOPMENT PICDEM LAB
DM164120-1
BOARD DEMO PICKIT 2 LP COUNT
DM164120-3
BOARD DEMO PICKIT2 28-PIN
DM164120-5
BOARD DEMO PICKIT 2 64/80-PIN
DM164123
KIT MANAGEMENT SYSTEM PICDEM
DM180021
KIT STARTER MPLAB FOR PIC18F MCU
DM183022
BOARD DEMO PIC18FXX22 64/80TQFP
DM183032
BOARD EXPLORER PICDEM PIC18
相关代理商/技术参数
DM163035
功能描述:开发板和工具包 - PIC / DSPIC PICDEM Lab Dev Kit RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压:
DM163035+TEFLCST3
制造商:Microchip Technology Inc 功能描述:KIT PICDEMLAB+FLOWCODE-HOME BUNDLE/ 制造商:Microchip Technology Inc 功能描述:PICDEM, FLOW CODE, LAB, DEV KIT
DM163045
功能描述:开发板和工具包 - PIC / DSPIC PICDEM Lab Dev Kit (with PICkit 3) RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压:
DM1-63-C
功能描述:端子 Metric Fem Disc non-insulated
RoHS:否 制造商:AVX 产品:Junction Box - Wire to Wire 系列:9826 线规:26-18 接线柱/接头大小: 绝缘: 颜色:Red 型式:Female 触点电镀:Tin over Nickel 触点材料:Beryllium Copper, Phosphor Bronze 端接类型:Crimp
DM1-63M-C
功能描述:端子 Metric Male Disc non-insulated, 0
RoHS:否 制造商:AVX 产品:Junction Box - Wire to Wire 系列:9826 线规:26-18 接线柱/接头大小: 绝缘: 颜色:Red 型式:Female 触点电镀:Tin over Nickel 触点材料:Beryllium Copper, Phosphor Bronze 端接类型:Crimp
DM164
制造商:SITI 制造商全称:SITI 功能描述:8x3-CHANNEL CONSTANT CURRENT LED DRIVER
DM1640
制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:16 characters x 4 line Liquid Crystal Dot Matrix Display Module
DM1640-0AL1
制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic